Novus Controller N1100 Manual de usuario descargar pdf (Pagina 1)

NOVUS AUTOMATION 1/8

Controller N1100

UNIVERSAL PROCESS CONTROLLER – INSTRUCTIONS MANUAL V2.1x

PRESENTATION

The N1100 is a process controller incorporating a PID algorithm and

universal inputs (sensor and standard signals) and outputs (logical,

relay and analog outputs). It holds in one single instrument all de main

features that are needed for the vast majority of industrial processes.

SAFETY SUMMARY

The symbols below are used on the equipment and throughout this

document to draw the user’s attention to important operational and

safety information.

CAUTION or WARNING:

Read complete instructions prior

to installation and operation of the

unit.

CAUTION or WARNING:

Electrical Shock Hazard

All safety related instructions that appear in the manual must be

observed to ensure personal safety and to prevent damage to either

the instrument or the system. If the instrument is used in a manner

not specified by the manufacturer, the protection provided by the

equipment may be impaired.

OVER-TEMPERATURE PROTECTION

When designing any control system it is essential to consider what

will happen if any part of the system should fail. In temperature

control applications the primary danger is one in which the heating

remains constantly on. In any application where physical injury or

destruction of equipment might occur, it is recommend to install an

independent protection equipment, with a separate temperature

sensor, to disable the heating circuit in case of overheating. Please

note that the alarm relays within the controller will not give protection

under all failure conditions.

INSTALLATION

Insert the unit into the panel cut-out and slide the mounting clamp

from the rear to a firm grip at the panel.

ELECTRICAL CONNECTIONS

All electrical connections are made to the screw terminals at the rear

of the controller. They accept wire sizes from 0.5 to 1.5 mm2 (16 to

22 AWG). The terminals should be tightened to a torque of 0.4 Nm

(3.5 lb in).

To minimize the pick-up of electrical noise, the low voltage DC

connections and the sensor input wiring should be routed away from

high-current power conductors. If this is impractical, use shielded

cables. In general, keep cable lengths to a minimum.

Figure 1 - Backpannel terminals

• Power Wiring

If high voltage is applied

to a low voltage input,

irreversible damage will

occur

Figure 2 – High and Low Voltage AC power wiring

• Thermocouple and Voltage (Volts and mV) input connect as in

Figure 3.

T/C, 0-50mV, 0-5V

Pt100

Figure 3 – T/C and Voltage wiring Figure 4 - RTD input wiring

1 2 3 4 5 6 7 8

Indice de contenidos

Pagina 1 - Controller N1100

NOVUS AUTOMATION 1/8 Controller N1100 UNIVERSAL PROCESS CONTROLLER – INSTRUCTIONS MANUAL V2.1x PRESENTATION The N1100 is a process controller i

Pagina 2 - OPERATION

Controller N1100 NOVUS AUTOMATION 2/8 • RTD (Pt100) Figure 4 shows the Pt100 wiring, for 3 conductors. Terminals 10, 11 and 12 must have the same

Pagina 3 - CONFIGURATION

Controller N1100 NOVUS AUTOMATION 3/8 CONFIGURATION INPUT TYPE SELECTION Select the input type (in parameter “tYPEtYPEtYPEtYPE”) from Table 1 below.

Pagina 4 - Table 3 - Alarm functions

Controller N1100 NOVUS AUTOMATION 4/8 TYPE PROMPT ACTION Disabled offoffoffoff No active alarm. This output can be used as a digital output to be s

Pagina 5 - CONFIGURATION PARAMETERS

Controller N1100 NOVUS AUTOMATION 5/8 CONFIGURATION PARAMETERS OPERATION CYCLE PV Indication (Red) SV Indication (Green) PV AND SV INDICATIO

Pagina 6 - Several

Controller N1100 NOVUS AUTOMATION 6/8 CONFIGURATION CYCLE typetypetypetype INPUT TYPE: Selects the input signal type to be connected to the proc

Pagina 7 - AUTO TUNE

Controller N1100 NOVUS AUTOMATION 7/8 EVENT ALARM This function makes possible to program the activation of alarms in specific segments of a program

Pagina 8 - WARRANTY

Controller N1100 NOVUS AUTOMATION 8/8 SERIAL COMMUNICATION The indicator can be supplied with an asynchronous RS-485 digital communication in

Mas documentos para Sensores Novus Controller N1100

a Ver el documento Novus Controller N1100 Manual de usuario

Novus Controller N1100 Manual de usuario (11 paginas)

Comentarios a estos manuales

Sin comentarios

Novus Controller N1100 Manual de usuario Pagina 1

Busca en linea o descarga Manual de usuario para Sensores Novus Controller N1100. NOVUS Controller N1100 User Manual Manual de usuario

Indice de contenidos

Mas documentos para Sensores Novus Controller N1100

Comentarios a estos manuales

Novus Controller N1100 Manual de usuario Pagina 1

Busca en linea o descarga Manual de usuario para Sensores Novus Controller N1100. NOVUS Controller N1100 User Manual Manual de usuario

Indice de contenidos

Mas documentos para Sensores Novus Controller N1100

Comentarios a estos manuales

Relacionado con productos y manuales para Sensores Novus Controller N1100